How To Install A 5 Channel Amp

Download Article

Bridging an amplifier combines the available channels into one aqueduct with half the ohm (Ω). Information technology is ordinarily used in car stereo systems, assuasive a powerful mono signal to exist sent to a subwoofer.

i
Make sure your amplifier tin be bridged. This should be indicated on the documentation pamphlets that came with the amplifier, or the amplifier itself. If the amplifier is used, or lacks documentation, get online and bank check for the specifications on the manufacturer's website.
- Bridging an amplifier cuts the resistance load (measured in ohms) in half, which can crusade information technology to overheat. Be certain to check your transmission (or the manufacturer's website) to see if one time connected to a speaker, whether or non your amplifier tin role at one-half the ohms it currently uses.
- Virtually amplifiers have a small diagram well-nigh the channels indicating the terminals you would use to bridge it. If your amplifier does non claim to exist able to span, don't try to span it. It may already be bridged internally, and you could cause damage to your amplifier.
- Be aware of the fact that if your amplifier is a stereo amplifier (amplifying both left and right), bridging it would cause it to go a mono amplifier (amplifying from one; either the left or correct).
two
Know the layout of your equipment. On your two-channel amp, yous should meet iv terminals: a positive (+) and a negative (-) for aqueduct one, and a positive (+) and a negative (-) for channel 2. Each terminal will be labeled as follows:
- Channel 1
  - "A" (positive)
  - "B" (negative)
- Aqueduct 2
  - "C" (positive)
  - "D" (negative)
Advertisement
3
Connect the amplifier to 1 speaker. From the wires coming out of the speaker, connect the positive speaker atomic number 82 to terminal A (the positive for channel 1) and connect the negative speaker lead to terminal D (the negative for channel 2). Connect these wires by unscrewing the screw in that concluding, placing the wire in between the top and lesser portions of the terminal, and then screw the screw down tightly to secure the wire.
- The wires coming from the speaker are going to be insulated with a plastic coating. You will demand to strip off a small portion of the wire insulation (less than ane inch) using a pair of wire strippers in society to secure information technology to the terminals.^[i]
- What this connectedness does is information technology combines the power from the 2 split channels, doubling your power output.^[ii]
Advertizement

1

Know your amplifier. Just similar method i, y'all must figure out if your iv-channel amplifier can be bridged. Taking nevertheless precautions, be certain to consult the amplifier manual or inquiry your amp model online to exist sure it can exist bridged.
2
Know the layout of your equipment. On your 4-aqueduct amp, you should run across 8 terminals: channels 1 through 4 each have a positive (+) and negative (-) terminal. Each terminal volition be labeled as follows:
- Aqueduct 1
  - "A" (positive)
  - "B" (negative)
- Channel 2
  - "C" (positive)
  - "D" (negative)
- Channel three
  - "Due east" (positive)
  - "F" (negative)
- Channel 4
  - "G" (positive)
  - "H" (negative)
3
Connect the amp to the kickoff speaker. From the wires coming out of the speaker, connect the positive speaker lead to terminal A (the positive for channel i) and connect the negative speaker lead to final D (the negative for channel 2). Again, just like bridging a two-channel amplifier, connect these speaker wires to the amplifier by unscrewing the screw in that whichever terminal you are connecting the wire to, place the wire in between the summit and bottom portions of the concluding, and and so screw the screw downwardly tightly to secure the wire.
- In one case the wires are secured, the first speaker is connected to the amplifier.
4

Connect the amp to the second speaker. Post-obit the previous method, again take the wires coming from the second speaker, just this time, connect the positive speaker lead to concluding E (the positive for channel 3) and connect the negative speaker atomic number 82 to terminal H (the negative for channel four).

Advertisement

Add New Question

Question

How can I play two speakers on one amp using bridged mode?

Y'all will demand a iv channel amp to run 2 speakers in bridged style. Typically the speakers will be hooked to the positive side of one channel and the negative side of some other thus bridging the channels, but this is not ever the example. Look for the diagram well-nigh the speaker connects to come across how yours is bridged. Once the speakers are hooked up, there will be a switch marked Stereo, Mono, or Bridged. Prepare this to Bridged.
Question

Can I connect one dual-ringlet speaker to a iv-channel amplifier?

Surely - this is possible. Just handle the two vocalisation coils like they were from 2 separate speakers. (And like the clarification of "Method 2".) Don`t interchange their connections (+ of one vc to - of another). But beware: you'd better feed the four channels with the same indicate (which means: all inputs fed from the same source,mono, not stereo), and surely not 4 unlike signals ("quadrophonic"), to go best results. Treat the voice roll's terminals as they're marked, + as +, - as -.
Question

How exercise I span my CD player to 2 carve up stereo receivers?

If your CD player has a line output, y'all are non going to be able to bridge it. Only amplifiers tin be bridged. You are but spltting the audio indicate into your receivers and you will demand a splitter for that.
Question

Can I span the four-channel amp like the two-channel amp?

If your amplifier is able to do that, yous can bridge the two in each pair together.
Question

Tin you show an image on how to bridge the wires on subs?

Kevin McGuire

Customs Answer

This is a simple, and requires no paradigm. Have i negative to one positive on each sub. Then run the other positive and negative to the box. Y'all tin can likewise reduce the ohms further by bridging it at the amp.
Question

Can I connect two woofers to a two aqueduct amplifier?

Dimitrios Hloros-Diehl

Community Answer

Yep, merely connect the left woofer's positive to the positive of the left channel on the amp and then practice the same for the negative. Repeat the procedure for the right woofer and the correct channel of your amp, positive to positive and negative to negative.
Question

What is crossover frequency?

The crossover frequency is the indicate in the graph of frequencies at which the "roll off" is started. It indicates the indicate at which you would normally have your amplifier for your main speakers start being total power.
Question

How practice I bridge an amplifier with ii mid range speakers and a subwoofer? It is a 4 channel amplifier.

Utilize channels 1 and 2 for chief Left and Correct and bridge the remaining channels for the subwoofer.
Question

How can I connect 2 woofers to a 4 channel amp?

Yes, you can either connect your get-go woofer to. For example, aqueduct 1 and your second woofer to aqueduct 2 or bridge your showtime woofer to channels 1 & ii and then bridge your second woofer to channels iii & 4.
Question

How do I bridge three subwoofers to a iv channel amp to get the about ability?

Span 2 channels to i of the subs and so i channel to each of your other subs, otherwise you lot have to merge all of your channels then dissever them which could be harmful to your amp.

Testify more answers

Ask a Question

200 characters left

Include your electronic mail address to get a message when this question is answered.

Submit

Video

Earlier trying to connect anything, you can quickly and easily consult an electronics or motorcar audio store.
Try to stay i level above the amplifiers lowest rated resistance. For case, if your amplifier says that it can handle ii Ohms, wire information technology so it produces iv Ohms. If you become lower than its displayed everyman rated resistance, your amp could shut off.

Thanks for submitting a tip for review!

Advertizing